Resonant Wireless Power Transfer (RWPT), introduced by MIT researchers in 2008, is a Wireless Power Transfer (WPT) that has compensation capacitors in both the transmitter and receiver and operating at their resonant frequency. The compensating capacitors make a big difference when compared to a WPT. They nullify the imaginary parts of the impedance seen by the source, thus, enabling the RWPT to achieve a higher output power and efficiency compared to the WPT. Such superiority is achievable not only at short distances but also at mid-range distances, relative to the coil size. No wonder, RWPT has been widely used, in recent years, in various technologies that require wireless power transfer such as appliances, wearable gadgets, mobile phones, and electric vehicle chargers, including the road-powered ones.
In this application note, a WPT system [2] is studied using EMWorks. The system is made of two copper printed coils. Figure 2 shows the simulated wireless system while Table 1 contains the main dimensions of the model. Later, we will add resonant capacitors to change the system from a WPT to RWPT and study the data resulting from such a change.
External coil | Interior coil | |
---|---|---|
Inner Diameter | 27.7 mm | 11.64 mm |
Outer Diameter | 41.3 mm | 16.14 mm |
Inter-traces distance | 1.4 mm | 0.3 mm |
Length of the trace | 1.6 mm | 0.5 mm |
Thickness of the traces | 40 um | 40 um |
Using EMS [3] module of EMWorks, we investigated the following RWPT issues:
Circuit parameters of the simulated RWPT including R and L matrices,
Coupling coefficient versus air gap and alignment,
Efficiency versus frequency and geometry configurations,
Comparison of EMS results against Powersim results.
Using the AC Magnetic module of EMS, the coils parameters including self and mutual inductances, AC resistances, and coupling coefficient are computed versus different air gap distances and alignments. These parameters are then used to compute the resonant capacitance and efficiency of the system.
Table 2 contains the AC inductance and resistances for an air gap of 15 mm.
External coil | Interior coil | |
---|---|---|
Self inductance M (H) | 1.774798e-006 | 1.281031e-006 |
Mutual inductance L1(H) | 1.207742e-007 | 1.207742e-007 |
Self resistance R (Ohm) | 3.410545e-001 | 6.161653e-001 |
Mutual resistance Rm(Ohm) | 1.920747e-003 | 1.920747e-003 |
From the above circuit parameters, the coupling coefficient between primary and secondary coils is computed. The greater is k the higher is the transmitted magnetic flux from the emitter to the receiver winding; hence, the efficiency is directly proportional to the coupling coefficient [4].
In addition to the above circuit parameters, the magnetic field and flux are computed. Figures 3a) and 3b) show the cross-section plots of the magnetic flux density results at 2 mm and 40 mm of air gap size, respectively. Clearly, the magnetic flux around the interior coil, i.e. receiver, is higher with an air gap of 2 mm compared to 40mm. Namely, 40 to 80 micro-Tesla versus 18 micro-Tesla for 2 and 40 mm, respectively.
The plots of the mutual inductance M and the coupling coefficient k versus the distance between the coils are shown in Figure 4. Clearly, M and k are inversely proportional to the distance separating the coils. Furthermore, with the help of the popular closed-form solution of the mutual inductance M, the inverse proportionality is cubic in nature since . Consequently, to achieve a good coupling coefficient, the coils must be as close as possible. How close? Well, it depends on the level of the coupling desired.
Figure 4 – Mutual inductance M and coupling coefficient k results versus air gap distance
As a matter of fact, the above conclusion is also applicable to the induced voltage, under open circuit operation, in the receiver coil, as shown in Figure 5.
The results of both mutual inductance M and coupling coefficient k, shown in Figure 6, are inspected versus axial alignment using another parametric study in EMS. The coupling between the coils drops only when the misalignment becomes larger than 15 mm. Hence, the studied system can operate at the same efficiency in a short range of misalignments up to 15 mm. This behavior can be attributed to the small size of the receiver.
Similarly, the induced voltage in the receiver coil is almost constant when for a misalignment less than 15mm and sharply decreases thereafter, as shown in Figure 7.
Figure 8 illustrates an animation of the magnetic flux density versus different misalignments. The magnetic flux density that reaches the receiver coil is almost constant up to a certain level of misalignment.
In the above investigated WPT system, the coupling coefficient is relatively low even at small air gap and aligned conditions. To illustrate the limitation of the WPT, we compute its efficiency as per the equation: , where V_{1} is the input voltage, I_{1} is the current in the primary side, is the phase between current and voltage,I_{load }is the current in the load, R_{load}and is the resistance of the load.
EMS circuit simulator is used to model the equivalent circuit of the simulated system as illustrated in Figure 9. Windings 1 and 2 are the coils of the WPT system. The input voltage is 2.5 V / 13.58MHz (phase shift is 0deg) and the load is a 10 Ohm resistance.
AC Magnetic module of EMS coupled to the circuit simulator are used to solve the WPT system. The transmitter and receiver are maintained at an aligned position and an air gap of 15 mm. The coupling coefficient is 0.08 at these conditions, as shown in Figure 4.
Table 3 contains the current results in the windings computed by EMS. Using the formula (3), the efficiency of the studied system is 0.17%, which is indeed low.
Current computed by EMS | |
---|---|
Winding 1 | 4.891836e-003 - j 1.479600e-002 |
Winding 2 | -5.844385e-004 + j 1.333585e-003 |
To improve its efficiency, resonant capacitors are added to the WPT system making it into a RWPT. In the following paragraphs, we shall compute the efficiency of the RWPT and compare it to that of a WPT system.
Figure 10 shows the new simulated circuit modeled using EMS circuit simulator. The resonant frequency is 13.58MHz while the resonant capacitors are respectively 77.26 pF and 114.42 pF computed based on the famous formula:
The input and output power of the studied RWPT system are computed versus frequency. Both input and output power show peak values at the resonant frequency, as illustrated in Figure 11.
Figure 12 shows the efficiency of the RWPT system versus different frequency. The efficiency is maximum at the resonant frequency. Without resonant capacitors, the efficiency is around 0.17% while it is close to 11% when the resonant capacitors are used. This proves that the resonant circuit helps in improving the efficiency, especially for applications with low coupling coefficients.
The impact of the load and the air gap distance on the efficiency of the RWPT system is investigated in the following section.
Figure 13 contains the efficiency results versus the air gap distance. The efficiency has a maximum value of around 19% in the range of 2 to 7 mm of air gap distance. It drops as the distance between the coils becomes larger, i.e. inversely proportional to the distance. Nonetheless, it is still more efficient than the WPT system, even at 30mm.
The load is varied from 1 Ohm to 50 Ohm and the efficiency of the simulated system is computed using the circuit quantities generated by EMS, as shown in Figure 17. The efficiency rises until reaching a maximum of 11% at a load of 10 Ohm then decreases. Therefore, the load must be carefully selected.
In this section, the results computed by EMS are compared to those obtained from and Powersim. The RWPT circuit is modeled in Powersim. Figure 15 shows the equivalent circuit of the system in Powersim. The parameters of the coupled inductor, used to model the wireless coils in Powersim, are given by EMS, as shown in Table 2.
Figure 16 shows the comparison of the computed efficiency calculated via EMS and Powersim. Clearly, the results show a very good agreement; actually matching results.
The system response as a function of frequency is analyzed using Powersim and the results are plotted in Figure 17. Bode diagram shows that the amplitude output curve has a maximum value of -16dB around the resonant frequency.
In this application note, we started by investigating a WPT system. We concluded that a WPT has an overall low efficiency, even at close distance between the coils. We then added two resonant capacitors to make the WPT into an RWPT. We demonstrated that indeed the RWPT is superior to the WPT. Nonetheless, the load must be carefully selected to achieve superior efficiency. In the last paragraph, we compared the EMS results for a RWPT system to those obtained via the commercial power software Powersim. A perfectly matched efficiency is obtained.